Houston blown in insulation is a more effective form of insulating an attic or wall cavity than standard rolled batting. It can also fit into small cracks or awkward shapes. It has the added benefit of being moisture-resistant. Here are the advantages of blown in insulation. Read on to find out what these benefits are and what you need to know about them. And don’t forget to ask your contractor for a quote!

Blowing-in insulation is more expensive than lower-quality alternatives, but it will pay off in energy savings. The extra cost of installation can be recovered in two to four years with the savings in utility bills. Because of its airtight seal, blown-in insulation can also be sound-absorbing, reducing the amount of noise that travels through walls. This can help protect the home from loud noises from outside. Therefore, it is a great choice for homes with open wall spaces.
However, blown-in insulation can be messy to install. If it’s too much, it may cause the ceiling to sag. And if you install too much insulation, you may end up with a damp, moldy attic. If it’s cellulose over fiberglass, you may have to refit your batts. Also, it’s possible that blown-in insulation will succumb to rot and mold if it comes in contact with water.
Although cellulose is safer than spray foam, it can still cause allergic reactions if not recycled. It’s also much more expensive than fiberglass, so many people choose to use fiberglass instead. Regardless of which type of insulation you choose, a well-insulated home will help keep utility costs down. But be sure to check out the pros and cons of each type of insulation before making your final decision. The benefits far outweigh the drawbacks.
While fiberglass batts are a better choice for older homes and newer buildings, blown-in insulation can be installed on closed-up walls without major remodeling projects. Blow-in insulation is easier to install than fiberglass batts and can boost the R-value of your walls. This makes it a good choice if you’re planning a remodel and need to improve the R-value of your walls. But if you’re not a homeowner, then blown-in insulation may be a good option for you.
Blown-in insulation is a messy process, so be sure to wear protective gear before you begin. You’ll also want to wear gloves and protective eyewear. The insulation can be dangerous, and you don’t want to slip and damage your drywall ceiling. Make sure you have a steady surface when working with blown-in insulation by setting up plywood or a tarp. You’ll be much safer if you have a partner to help you!
Blown-in insulation can cost between $1.90 and $4.20 per square foot. Rockwool, on the other hand, isn’t as widely available as cellulose. But it offers a natural fire resistance, high R-value, and better sound dampening. Rockwool is made of basalt, a mineral that is similar to sheep’s wool. The only downside to rock wool is the price – it can cost up to four dollars per square foot. Besides, rockwool doesn’t come with a warranty, so you can re-use your old insulation if you want.
Blown-in cellulose is safe around most recessed cans and contemporary light fixtures. Antique light fixtures and wiring may not be fire-rated, so your insulation contractor will need to recommend another type. Blown-in cellulose is not necessarily more expensive than fiberglass; the price difference is comparable. And it’s more environmentally friendly. You can choose the type of insulation that best meets your needs. A few things you should know about this type of insulation.
Another advantage of cellulose blown-in insulation is that it can fit into tight spaces and odd shapes. Though it is less efficient than fiberglass, it is less prone to airflow than fiberglass. For this reason, it is best installed with a dense-pack method. It is important to remember that cellulose insulation requires that you remove some siding temporarily before putting it up. If you are planning to install this type of insulation, make sure you have enough space to fit it in your home.
Blown-in insulation is usually more expensive than other types of insulation. However, it is worth the price since it has a higher R-value due to its quality and consistency of application. But if you’re looking for an economical option, you should look into blown-in insulation instead. There are many advantages to this type of insulation. You can save money on utility bills and get a quality installation. However, there are some disadvantages to this type of insulation.